以下是抽油煙機常見故障問題及客戶可自行處理的方法,如無法解決可聯繫我們上門專業維修Below are common range hood faults and self-help solutions. Contact us for professional on-site repair if the problem persists
抽油煙機不啟動Range hood not starting
原因:
電源插頭鬆脫或斷電
電源開關故障
保險絲燒斷
電機故障
自行處理方法:
檢查電源插頭是否插緊,更換插座測試
檢查電源開關是否正常
查看保險絲是否燒斷,更換同規格保險絲
如以上方法無效,請聯繫專業維修
Causes:
Loose power plug or power outage
Power switch failure
Blown fuse
Motor failure
Self-help solutions:
Check if power plug is tight, test with another socket
Check if power switch is working properly
Check if fuse is blown, replace with same specification
Contact professional repair if above methods fail
抽油煙機通電但不轉Range hood powered but not rotating
原因:
電容損壞
電機卡死
風輪被異物卡住
控制電路故障
自行處理方法:
切斷電源後檢查風輪是否有異物卡住
輕輕轉動風輪,檢查是否卡死
如發現異物,小心移除後重新測試
電容損壞需專業人員更換
Causes:
Damaged capacitor
Motor seized
Fan wheel jammed by foreign objects
Control circuit failure
Self-help solutions:
Check for foreign objects jamming fan wheel after power off
Gently rotate fan wheel to check for seizure
Carefully remove any foreign objects and retest
Capacitor damage requires professional replacement
抽油煙機噪音很大嗡嗡響Loud buzzing noise from range hood
原因:
風輪積油過多不平衡
安裝不牢固,螺絲鬆動
電機軸承磨損
風輪變形或損壞
自行處理方法:
定期清潔風輪積油,保持平衡
檢查安裝螺絲是否鬆動,及時擰緊
避免異物進入風輪內部
軸承磨損需更換,請聯繫專業維修
Causes:
Excessive oil accumulation on fan wheel causing imbalance
Loose installation screws
Worn motor bearings
Deformed or damaged fan wheel
Self-help solutions:
Regularly clean oil accumulation on fan wheel to maintain balance
Check and tighten loose installation screws
Prevent foreign objects from entering fan wheel
Bearing wear requires replacement by professionals
抽油煙機吸力變小Reduced suction power of range hood
原因:
油網積油過多堵塞
煙道堵塞
風輪積油嚴重
電機老化功率下降
自行處理方法:
定期清洗油網,保持通暢
檢查煙道是否堵塞,及時清理
清洗風輪積油,恢復轉動效率
檢查排風口是否被阻擋
Causes:
Excessive oil accumulation blocking oil mesh
Blocked flue
Severe oil accumulation on fan wheel
Motor aging with reduced power
Self-help solutions:
Regularly clean oil mesh to keep it clear
Check and clear blocked flue
Clean oil accumulation on fan wheel to restore rotation efficiency
Check if air outlet is blocked
抽油煙機倒灌油煙嚴重Severe oil fume backflow
原因:
止回閥故障或安裝不當
公共煙道壓力過大
排風管徑過小或彎曲過多
抽油煙機功率不足
自行處理方法:
檢查止回閥是否靈活,清理積油
確保止回閥安裝方向正確
檢查排風管是否暢通,減少彎曲
高峰期使用時適當開窗通風
Causes:
Check valve failure or improper installation
Excessive pressure in public flue
Exhaust pipe diameter too small or too many bends
Insufficient range hood power
Self-help solutions:
Check if check valve is flexible and clean oil accumulation
Ensure check valve is installed in correct direction
Check exhaust pipe for blockages and reduce bends
Open windows for ventilation during peak usage hours
抽油煙機漏油滴水Range hood oil leakage and dripping
原因:
油杯滿溢未及時清理
油網破損或安裝不當
機身內部積油過多
排風管接縫不嚴
自行處理方法:
及時清理油杯積油
檢查油網是否完好,正確安裝
定期清洗機身內部
檢查排風管接縫,必要時重新密封
Causes:
Oil cup overflow due to infrequent cleaning
Damaged or improperly installed oil mesh
Excessive oil accumulation inside the unit
Loose exhaust pipe joints
Self-help solutions:
Regularly clean oil accumulation in oil cup
Check oil mesh condition and install correctly
Regularly clean inside the unit
Check exhaust pipe joints and reseal if necessary
抽油煙機自動開關機失靈Automatic on/off malfunction
原因:
按鍵面板故障
控制電路板損壞
紅外感應器故障
電源接觸不良
自行處理方法:
清潔按鍵面板,去除油污
切斷電源重啟嘗試
檢查電源連接是否穩定
如無效,需更換控制面板或電路板
Causes:
Button panel failure
Damaged control circuit board
IR sensor malfunction
Poor power connection
Self-help solutions:
Clean button panel to remove oil stains
Power off and restart
Check stable power connection
Replace control panel or circuit board if ineffective
深水埗區:深水埗、長沙灣、荔枝角Sham Shui Po: Sham Shui Po, Cheung Sha Wan, Lai Chi Kok
九龍城區:九龍城、九龍塘、何文田、紅磡Kowloon City: Kowloon City, Kowloon Tong, Ho Man Tin, Hung Hom
黃大仙區:黃大仙、慈雲山、樂富、新蒲崗Wong Tai Sin: Wong Tai Sin, Tsz Wan Shan, Lok Fu, San Po Kong
觀塘區:觀塘、藍田、將軍澳Kwun Tong: Kwun Tong, Lam Tin, Tseung Kwan O
新界
New Territories
荃灣區:荃灣、馬灣Tsuen Wan: Tsuen Wan, Ma Wan
屯門區:屯門Tuen Mun: Tuen Mun
元朗區:元朗、天水圍Yuen Long: Yuen Long, Tin Shui Wai
北區:上水、粉嶺、打鼓嶺North: Sheung Shui, Fanling, Ta Kwu Ling
大埔區:大埔、吐露港、船灣淡水湖Tai Po: Tai Po, Tolo Harbour, Plover Cove Reservoir
沙田區:沙田、大圍、馬鞍山Sha Tin: Sha Tin, Tai Wai, Ma On Shan
西貢區:西貢、將軍澳Sai Kung: Sai Kung, Tseung Kwan O
公司地址Company Address
香港九龍觀塘駿業裏10號業運工業大廈5D
5D, Yip Win Industrial Building, 10 Chun Yip Lane, Kwun Tong, Kowloon, Hong Kong
客戶好評與成功案例Customer Reviews & Success Cases
我們的專業服務獲得客戶一致好評Our professional services have received consistent praise from customers
5.0
「抽油煙機夜間一直自動響,聯繫了這家公司,師傅很快就上門維修,態度專業,價格合理,修完後再也沒有出現問題,非常推薦!」「My range hood kept making noise at night automatically. I contacted this company, and the technician came to repair it quickly with professional attitude and reasonable price. No more problems after repair, highly recommended!」
陳小姐 - 銅鑼灣
Ms. Chan - Causeway Bay
抽油煙機休眠故障維修
Range hood sleep mode fault repair
5.0
「抽油煙機吸力變小,師傅上門檢查後發現是風輪積油太多,清洗後吸力恢復正常,收費透明,服務很好!」「My range hood had reduced suction power. The technician checked and found excessive oil accumulation on the fan wheel. Suction restored to normal after cleaning, transparent pricing and excellent service!」
李先生 - 旺角
Mr. Lee - Mong Kok
抽油煙機吸力小維修
Range hood low suction repair
4.5
「紅酒櫃壞了,聯繫了多家維修公司都不修,這家公司專業維修進口紅酒櫃,師傅技術好,很快就修好了,非常感謝!」「My wine cabinet broke down, and many repair companies refused to fix it. This company specializes in repairing imported wine cabinets with skilled technicians who fixed it quickly, thank you very much!」